What size are toilet bolt nuts?

What size are toilet bolt nuts? The most common size supply tube connection to the valve is a 3/8-inch hexagon compression nut. If you’re not sure what the size is, or it is not 3/8 inch, you can always remove the supply tube and take it with you for comparison when purchasing a new supply tube.

How much does it cost to tighten toilet bolts? Because porcelain toilets are relatively brittle, it’s important to tighten toilet tank bolts carefully. The best way to do so is to hand-tighten the nuts on the tank bolts, then use a wrench to make a quarter-turn on each nut.

Can you replace toilet bolts without removing toilet? You can’t replace a closet bolt without removing the bowl. Pull the bowl, and next time pick up brass bolts.

What is the purpose of toilet bolt caps? When you install a toilet, one of the finishing touches is to cover the flange bolts — the bolts that hold the toilet to the floor — with decorative caps. These caps aren’t just for show; they protect the bolts from corroding in the moist conditions in the bathroom.

What size are toilet bolt nuts? – Related Questions

What are toilet bolts called?

Securing your toilet to the floor are two long bolts (called closet bolts) that come up through the base of the toilet and are secured with nuts.

Are all toilet bolts the same size?

There are three possible measurement distances you can get from the wall to the toilet bolt: 10 inches, 12 inches, or 14 inches. The most common is 12 inches. In plumbing terminology, this is called a 12-inch rough. Sometimes these measurements are not exact.

Can you over tighten toilet tank bolts?

If you tighten it too much, you can pull the closet bolt out through the flange, ruining the flange or breaking the porcelain. DO NOT tighten it as tight as it will go, like you’re building something or working on your car – you’ll break the flange, chip or crack the porcelain or both.

Why do toilet anchor bolts rust?

Moisture around the base of the toilet can corrode the anchor bolts. This moisture may be the result of water escaping from the toilet because of an imperfect seal or, in basements near sea level, it may come from condensation or poor drainage.

How often should you replace the wax ring on a toilet?

It requires no maintenance and can last 30 or more years, often as long as the toilet itself. But sometimes wax rings can dry out, crumble, and fail prematurely. When that happens, they need to be replaced. The telltale sign of wax ring failure is water leaking out from around the base of the toilet.

Where is the toilet flapper?

The flapper (aka “flush valve seal”) is the plug that falls against the drain hole (flush valve drain seat) on the bottom of the tank and holds water in until the next time you flush.

Do you need to bolt a toilet to the floor?

Your toilet should be fixed to the floor using several bolts. Carefully unscrew the nuts and washers to help free the toilet. Your toilet may also have silicone around the base to make it more secure. Use a screwdriver to pick these off to expose the bolts.

Are toilet bolts universal?

One pair bolts with double nuts and washers for toilet upside and bottom. 3. Universal fit for most toilet.

Should I cover toilet hole?

Yes, you do have to plug (cover) the hole to keep sewer gases from coming through.

How do you cover a toilet floor hole?

You can use the cover from a tub of ice cream, the lid from a gallon can of paint, or just cover it with duct tape. if your renovations include new tile on floor, then make sure your flange is at floor level when finished.

Is it safe to leave a toilet off overnight?

Yes, absolutely, fumes can be harmful when replacing a toilet, but they can be kept at a minimum and shouldn’t pose a health risk if you work reasonably quickly and keep the drainpipe covered between removal and installation.

Why does my toilet moves side to side?

If the flange is a little higher than the surrounding flooring, the toilet becomes raised slightly in the center, allowing it to rock to either side. This problem can develop over time, such as when the wax seal becomes faulty or when a surrounding floor settles a little.

Why is my toilet loose from the floor?

Toilets wobble when they aren’t held securely to the floor, and if you let the wobble persist, they can leak and give you more serious problems. More often than not, the wobble is caused by loose toilet bolts, but the flange may also be responsible. It may be corroded, broken or set too high.

Are tank to bowl bolts universal?

Manufactured in a high quality, chlorine resistant rubber, the Korky tank to bowl gaskets are universal to fit most toilet tanks.

What happens if you overtighten toilet bolts?

Toilets are made of vitreous china and if you put too much stress on them they can crack. If you continue to tighten toilet bolts, the toilet will crack, so you have to know when to stop. The only problem is that usually only comes with experience. I would first suggest using a very small wrench.

How do I remove old rusted toilet bolts?

Use a deep well socket to reach the nut on the underside of the toilet and attempt to loosen it. Use a Dremel tool with a cutting blade to cut through the bolt and nut. Use an oscillating tool to cut through the bolt and nut. Tape off the area around the bolts and cut the tops off the bolts using a mini hacksaw.

Are there different sizes of wax rings for toilets?

Wax rings come in two diameters, 3 inches and 4 inches, because — as you might expect — those are the two standard sizes for toilet waste openings. Besides diameter, thickness is also an important parameter when it comes to wax rings. Again, there are two possibilities: regular and extra thick.

How do I know if my toilet needs a new wax ring?

The first sign of a failing wax ring is water that seems to be seeping out of the base of your toilet. Other signs to look for include: Water stains on the ceiling from the floor below. A lingering, unpleasant bathroom odor from escaped sewer gasses.

Is a wobbly toilet bad?

Fortunately, a rocking toilet isn’t going to cause you much personal harm, but a loose, wobbly toilet is still something you should fix. This is actually kind of important since it can eventually lead to sewer gas leakage or worse, a water leak that can damage your home.

Are toilet flappers standard size?

Flappers comes in two sizes, two inch and three inch. A majority of toilets will use the two inch flapper; however three inch flappers have become popular in recent years and can be found in newer toilets manufactured since 2005.